Rings:

№ 1.099	Rings • standard ring № 1.099(5) - tines height - 5 mm • low ring № 1.099(4) - tines height - 4 mm • high ring № 1.099(6) - tines height - 6 mm	Tines of ring № 1.099	Scheme on tooth

№ 1.099A	Ring Ring № 1.099А has the same construction of tines as standard ring № 1.099 for sectional matrices. Addition of extra loop on the ring makes it more flexible and allows to operate in wider range of opening without increase of residual distance between tines after use.	Tines of ring № 1.099A	Scheme on tooth

№ 1.099c	Ring with silicone safety cover autoclavable	Tines of ring № 1.099c	Scheme on tooth

№ 1.199	Ring	Tines of ring № 1.199	Scheme on tooth

№ 1.299	Delta Ring Double tines of Delta ring are suitable for installation of fixing wedges and add-on wedges.	Tines of ring № 1.299	Scheme on tooth

№ 1.299c	Delta Ring Ledges (shoulders) on Delta ring № 1.299с prevent getting of tongue into operating area.	Tines of ring № 1.299c	Scheme on tooth

№ 1.167	MD Ring Tines of MD ring provide the most non-fluctuating placement with sufficient space for wedge.	Tines of ring № 1.167	Scheme on tooth

№ 1.167c	MD Ring Ledges (shoulders) on MD ring № 1.167с prevent getting of tongue into operating area.	Tines of ring № 1.167c	Scheme on tooth

№ 1.166	D Ring Tines of D ring are curved inwards to fix matrix on distal side of the tooth.	Tines of ring № 1.166	Scheme on tooth

№ 1.177	M Ring Tines of M ring are curved out to fix matrix on mesial side of the tooth.	Tines of ring № 1.177	Scheme on tooth

№ 1.033	Ring for saddle matrices		Tines of ring № 1.033

№ 1.033А	Ring for saddle matrices Ring № 1.033А has the same construction of tines as standard ring № 1.033 for saddle matrices. Addition of extra loop on the ring makes it more flexible and allows to operate in wider range of opening without increase of residual distance between tines after use.		Tines of ring № 1.033А

№ 1.033c	Ring for saddle matrices with silicone safety cover autoclavable		Tines of ring № 1.033с

№ 1.022	Ring for perforated matrices		Tines of ring № 1.022

№ 1.044	Slot Ring	Tines of ring № 1.044	Scheme on tooth

WARNING!!!
When operating with ring:
1) make sure of integrity of the ring and absence of rust on it;
2) avoid high-speed opening;
3) open the ring for width not more than 10 - 12 mm;
4) open the ring for necessary width outside the mouth before placing it on a tooth.

Cleaning and sterilization instructions:

1) Submerge instruments in cleaning agent solution with neutral pH for 20 min;
2) Rinse the instruments thoroughly with purified water for 3-5 min;
3) Perform standard moist heat / steam sterilization procedure following the sterilizer instructions.

WARNING!!!
1) Do not use cleaning agents with high percentage of chlorine and cleaners containing oxalic acid;
2) Do not keep instruments in liquid medium for more than 3 hours.

to the top

Rings:

№ 1.099

№ 1.099A

№ 1.099c

Ring

№ 1.199

Ring

№ 1.299

Delta Ring

№ 1.299c

Delta Ring

№ 1.167

MD Ring

№ 1.167c

MD Ring

№ 1.166

D Ring

№ 1.177

M Ring

№ 1.033

Ring for saddle matrices

№ 1.033А

№ 1.033c

Ring for saddle matrices

№ 1.022

Ring for perforated matrices

№ 1.044

Slot Ring

Cleaning and sterilization instructions: